• Repairing Cracks In Thermalite Blocks Sizes Concrete
• Repairing Cracks In Thermalite Blocks Sizes Chart
• Thermalite Lightweight Building Blocks
• Thermalite Blocks Lowe's

The crack in question is in an integral garage ( right hand side as you look at the picture of the house ), is hairline, runs pretty much vertical, through mortar in places and in other places straight through the blocks (which I think are thermalite but may very well be wrong ) themselves. Cracks in Brick Walls &: Foundations - How to recognize, diagnose, & repair or prevent brick wall or foundation cracks due to thermal expansion Factors that determine the extent of thermal expansion damage to a brick wall or structure Absence of control joints or expansion joints in long brick walls leads to extensive cracking damage Photographs of foundation damage patterns and types of.

Ask a tradesman

Bricklaying

We recently had a conservatory built (during very wet and cold weather), last week I noticed a vertical hairline crack running from top to bottom on one wall (wall is 4.5M wide). when the render was tapped it sounded hollow or live. Working with a small screwdriver of part of the crack a 2.5M x 1.5M section of render simply fell off and the whole of this wall sounds live although the other two walls seem sound. It can now be seen that the uniform hairline crack goes the entire height of the wall and there appears to be another starting about a meter further down. I called the company back and they are sending the builder to have a look before they have it re-rendered. I understand that thermalite can shrink and crack as the blocks were saturated when laid. Question is what is the correct procedure now?

There are three hairline cracks running the entire height of the wall from damp-course to the leaded top of the wall, nothing below the damp-course which is concrete block. The cracks are even top to bottom and are less than a millimetre in width. The was just one crack visible before the render came off then two more are revealed but the render over these was not effected.

The wall was built and rendered in February when the weather was both wet and cold but not at frost conditions, the blocks were saturated and since the wall faces South the unusually hot sun this year has pitched on the wall for about ten hours each day.

The builder has said he will do whatever is necessary to remedy it but doesn’t seem too sure as to how to proceed. I have suggested that he angle grinds a half inch gap along the crack and then fill with a expanding joint mastic of some sort – not sure if this is the right way to go, then finally PVA the wall and re-render.

4

4 Answers from MyBuilder Bricklayers

Best Answer

72434

is a thermal shock
due to warm and cold water you must use elastic and heat resistant material

2018-08-12T10:25:01+01:00

Answered 12th Aug 2018

72444

Yes blocks do crack in extreme weather.i would take off render.put mesh on then render.never crack again.even if blockwork cracked.

2018-08-12T19:30:02+01:00

Answered 12th Aug 2018

72495

Repairing Cracks In Thermalite Blocks Sizes Concrete

Hack it all off and dot and dab. Thermalite and hardwall dont mix

2018-08-13T21:50:02+01:00

Answered 13th Aug 2018

Repairing Cracks In Thermalite Blocks Sizes Chart

72770

Hi.

If the render appeared ‘live’ before falling off, it is the bond between block and render that is at fault. Possibly caused by a combination of excessively wet block (although rendering wet blocks can be ok) and an overly weak mix. If it was cold during the build and the render was affected you frost, this could also account for problems.

I would take issue with ‘.....blocks do crack in extreme weather....’ speak to any block manufacturer for clarification of this.

Occasionally a block WALL may crack in extremely dry conditions if it’s foundation bears on highly plastic soil, and this shrinks due to reduced moisture content (dry summers/demand from proximal vegetation). I have never known a single BLOCK to crack -50<T<50 degrees C.

I would advise against simply meshing and rendering if there is a prob with the blockwork. You do not state wether the crack is in the block as well as the render. If the blocks are cracked, there could be an issue with the footing. Crack wider at the top?

If you give me a bit more info. I’d be happy to advise how you should deal with the installer

2018-08-23T19:00:02+01:00

Answered 23rd Aug 2018

Related Questions

• Massive hair line cracking across rooms and blown plaster - Why? And what to do next?

  We had some walls in a 1930's house skimmed approx 2 years ago, we have seen hairline cracking appearing accross whole walls and...

• Cracking Render

  Hi, we have had an internal alleyway rendered. It is not heated, but it is protected from the elements. One wall is new and is a...

• Damp proofing render has cracked extensively

  I live in a basement flat and when we moved in 4/5 months ago we had the living room/kitchen (one room) and bathroom treated for...

• Removing and replacing render in late September/ October

  Hi. The render on the front of my house is blown (and a big patch removed). Is It (end September) too late to instruct someone...

We have removed the pebbledash from our 30s house which had an extension added to it in the 80s made from 'solid' 9' thermalite blocks. This has revealed a few cracks that go straight through the blocks. These are only a couple of mm wide but this is the time to sort it out. The plasterer has suggested that a sheet of expanded metal over the area should sort it out. Is this a sensible option?

Thermalite Lightweight Building Blocks

I guess if it were 2 leaves of brick I would cut out the damaged brickwork and replace but it seems to be more difficult with a solid wall and supporting the existing wall plate.
What about stitching the damaged area? Would this be worth it or just go with the expanded metal.
Thanks in advance.

Thermalite Blocks Lowe's

Matt